GENERAL DESCRIPTION
Duratron ® T PAI is the highest performing melt processable plastic. It has superior resistance to elevated temperatures. It is capable of performing under severe stress conditions at continuous temperatures to 500°F (260°C). Parts machined from Duratron ® T PAI stock shapes provide greater compressive strength and higher impact resistance than most advanced engineering plastics. Its extremely low coefficient of linear thermal expansion and high creep resistance deliver excellent dimensional stability over its entire use range. PAI is an amorphous material with a Tg (glass transition temperature) of 537°F (280°C).
Duratron T4301 PAI (Extruded)
Duratron ® T4301 extruded PAI is primarily used for wear and friction parts. This grade contains 12% graphite powder and 3% PTFE for a very low expansion rate, low coefficient of friction and little or no slip-stick in use. This grade excels in severe service wear applications such as non- lubricated bearings, seals, bearing cages and reciprocating compressor parts.
Extruded Duratron ® T4301 PAI is typically only available in thin sheets and small diameter rods. Check with us for availability of T4301 in the size you need.
See also Duratron T4501 Compression Molded PAI specification for comparison, or these two bearing grades side-by-side here.
For a complete overview of Quadrant's Duratron product family, including other high-performance engineering plastics, see this page.
|
TYPICAL PROPERTIES of DURATRON® T4301 PAI POLYAMIDE-IMIDE | ||
| ASTM or UL test | Property | Duratron T4301 PAI Extruded |
| PHYSICAL | ||
| D792 | Density (lb/in³) (g/cm³) |
0.052 1.45 |
| D570 | Water Absorption, 24 hrs (%) | 0.4 |
| D570 | Water Absorption, Saturation (%) | 1.5 |
| MECHANICAL | ||
| D638 | Tensile Strength (psi) | 15,000 |
| D638 | Tensile Modulus (psi) | 900,000 |
| D638 | Tensile Elongation at Break (%) | 3.0 |
| D790 | Flexural Strength (psi) | 23,000 |
| D790 | Flexural Modulus (psi) | 800,000 |
| D732 | Shear Strength (psi) | 16,400 |
| D695 | Compressive Strength (psi) | 22,000 |
| D695 | Compressive Modulus (psi) | 950,000 |
| D785 | Hardness, Rockwell | E70(M106) |
| D256 | IZOD Notched Impact (ft-lb/in) | 0.8 |
| PTM 55007 | Coefficient of Friction (Dry vs. Steel) Dynamic | 0.20 |
| PTM 55007 | Limiting PV (4:1 Safety Factor) (ft-lb-in2-min | 22,500 |
| PTM 55010 | Wear Factor "k" x 10-10(in3-min/ft-lb-hr | 10 |
| THERMAL | ||
| D696 | Coefficient of Linear Thermal Expansion (x 10-5 in./in./°F) |
1.4 |
| D648 | Heat Deflection Temp (°F / °C) at 264 psi |
534 / 277 |
| D3418 | Glass Transition Temp (°F / °C) | 527 / 275 |
| - | Max Operating Temp (°F / °C) | 500 / 260 |
| C177 | Thermal Conductivity (BTU-in/ft²-hr-°F) (x 10-4 cal/cm-sec-°C) |
3.70 12.75 |
| UL94 | Flammability Rating | V-0 |
| ELECTRICAL | ||
| D149 | Dielectric Strength (V/mil) short time, 1/8" thick | - |
| D150 | Dielectric Constant at 1 MHz | 6.0 |
| D150 | Dissipation Factor at 1 MHz | 0.037 |
| EOS/ESD S11.11 | Surface Resistivity (ohms/square) | > 1013 |
NOTE: The information contained herein are typical values intended for reference and comparison purposes only. They should NOT be used as a basis for design specifications or quality control. Contact us for manufacturers' complete material property datasheets.DURATRON is a registered trademark of Quadrant Engineering Plastic Products.
All values at 73°F (23°C) unless otherwise noted.
©
Copyright Boedeker Plastics, Inc.