GENERAL DESCRIPTION
Duratron ® T PAI is the highest performing melt processable plastic. It has superior resistance to elevated temperatures. It is capable of performing under severe stress conditions at continuous temperatures to 500°F (260°C). Parts machined from Duratron ® T PAI stock shapes provide greater compressive strength and higher impact resistance than most advanced engineering plastics. Its extremely low coefficient of linear thermal expansion and high creep resistance deliver excellent dimensional stability over its entire use range. PAI is an amorphous material with a Tg (glass transition temperature) of 537°F (280°C).
Duratron T7130 PAI (Extruded)
Duratron ® T7130 is 30% carbon reinforced, extruded PAI. It offers exceptional stiffness, nonabrasive wear performance and the lowest coefficient of thermal expansion and the best fatigue resistance of all plastic materials. Key applications for T7130 PAI include metal replacement, sliding vanes, aerospace parts, impellers, shrouds, pistons, and housings. NOTE: Duratron T7130 was also formerly known as Torlon 4XCF.
Extruded Duratron ® T7130 PAI is typically only available in thin sheets and small diameter rods. Check with us for availability of T7130 in the size you need.
NOTE: This less-common carbon-reinforced grade is NOT AVAILABLE FROM STOCK, but rather can be offered ONLY BY SPECIAL ORDER ... long leadtimes and large minimum order quantities may apply when ordering this grade in sheet or rod forms.
See also Duratron T7530 Compression Molded PAI specification for comparison, or these two carbon-reinforced grades side-by-side here.
For a complete overview of Quadrant's Duratron product family, including other high-performance engineering plastics, see this page.
|
TYPICAL PROPERTIES of DURATRON® T7130 PAI PolyAmide-Imide | ||
| ASTM or UL test | Property | Duratron® T7130 Extruded |
| PHYSICAL | ||
| D792 | Density (lb/in³) (g/cm³) |
0.058 1.60 |
/TR>
| D570 | Water Absorption, 24 hrs (%) | 0.3 |
| D570 | Water Absorption, Saturation (%) | 1.5 |
| MECHANICAL | ||
| D638 | Tensile Strength (psi) | 23,000 |
| D638 | Tensile Modulus (psi) | 1,000,000 |
| D638 | Tensile Elongation at Break (%) | 4.0 |
| D790 | Flexural Strength (psi) | 30,000 |
| D790 | Flexural Modulus (psi) | 980,000 |
| D732 | Shear Strength (psi) | - |
| D695 | Compressive Strength (psi) | 40,000 |
| D695 | Compressive Modulus (psi) | 700,000 |
| D785 | Hardness, Rockwell | E90 |
| D256 | IZOD Notched Impact (ft-lb/in) | 1.0 |
| PTM 55007 | Coefficient of Friction (Dry vs. Steel) Dynamic | - |
| PTM 55007 | Limiting PV (4:1 Safety Factor) (ft-lb-in2-min | - |
| PTM 55010 | Wear Factor "k" x 10-10(in3-min/ft-lb-hr | - |
| THERMAL | ||
| E-831 | Coefficient of Linear Thermal Expansion (x 10-5 in./in./°F) |
0.9 |
| D648 | Heat Deflection Temp (°F / °C) at 264 psi |
- |
| D3418 | Glass Transition Temp (°F / °C) | 527 / 275 |
| - | Max Operating Temp (°F / °C) | 500 / 260 |
| C177 | Thermal Conductivity (BTU-in/ft²-hr-°F) (x 10-4 cal/cm-sec-°C) |
2.5 8.6 |
| UL94 | Flammability Rating | V-0 |
| ELECTRICAL | ||
| D149 | Dielectric Strength (V/mil) short time, 1/8" thick | 700 |
| D150 | Dielectric Constant at 1 MHz | 6.3 |
| D150 | Dissipation Factor at 1 MHz | 0.050 |
| EOS/ESD S11.11 | Surface Resistivity (ohms/square) | > 1013 |
NOTE: The information contained herein are typical values intended for reference and comparison purposes only. They should NOT be used as a basis for design specifications or quality control. Contact us for manufacturers' complete material property datasheets.DURATRON is a registered trademark of Quadrant Engineering Plastic Products.
All values at 73°F (23°C) unless otherwise noted.
©
Copyright Boedeker Plastics, Inc.