GENERAL DESCRIPTION
Duratron ® T PAI is the highest performing melt processable plastic. It has superior resistance to elevated temperatures. It is capable of performing under severe stress conditions at continuous temperatures to 500°F (260°C). Parts machined from Duratron ® T PAI stock shapes provide greater compressive strength and higher impact resistance than most advanced engineering plastics. Its extremely low coefficient of linear thermal expansion and high creep resistance deliver excellent dimensional stability over its entire use range. PAI is an amorphous material with a Tg (glass transition temperature) of 537°F (280°C).
Duratron T5530 PAI (Compression Molded)
Duratron ® T5530 is 30% glass reinforced, compression molded PAI. It is ideal for higher load structural or electronic applications. It is selected for larger shapes or when the greatest degree of dimensional control is required. Applications include burn-in sockets, gears, valve plates, impellers, rotors, terminal strips, and insulators.
Compression-molded Duratron ® T5530 is typically available only in larger diameter rods (in short lengths), thicker sheets, and large (but short length) tubes. Check with us for availability of T5530 in the size you need.
See also Duratron T5030 Extruded PAI specification for comparison, or these two glass-reinforced grades side-by-side here.
For a complete overview of Quadrant's Duratron product family, including other high-performance engineering plastics, see this page.
|
TYPICAL PROPERTIES of DURATRON® T5530 PAI PolyAmide-Imide | ||
| ASTM or UL test | Property | Duratron® T5530 Compression Molded |
| PHYSICAL | ||
| D792 | Density (lb/in³) (g/cm³) |
0.058 1.61 |
| D570 | Water Absorption, 24 hrs (%) | 0.3 |
| D570 | Water Absorption, Saturation (%) | 1.5 |
| MECHANICAL | ||
| D638 | Tensile Strength (psi) | 15,000 |
| D638 | Tensile Modulus (psi) | 900,000 |
| D638 | Tensile Elongation at Break (%) | 3.0 |
| D790 | Flexural Strength (psi) | 20,000 |
| D790 | Flexural Modulus (psi) | 900,000 |
| D732 | Shear Strength (psi) | - |
| D695 | Compressive Strength (psi) | 27,000 |
| D695 | Compressive Modulus (psi) | 600,000 |
| D785 | Hardness, Rockwell | E85(M106) |
| D256 | IZOD Notched Impact (ft-lb/in) | 0.7 |
| PTM 55007 | Coefficient of Friction (Dry vs. Steel) Dynamic | 0.20 |
| PTM 55007 | Limiting PV (4:1 Safety Factor) (ft-lb-in2-min | 20,000 |
| PTM 55010 | Wear Factor "k" x 10-10(in3-min/ft-lb-hr | - |
| THERMAL | ||
| E-831 | Coefficient of Linear Thermal Expansion (x 10-5 in./in./°F) |
2.6 |
| D648 | Heat Deflection Temp (°F / °C) at 264 psi |
520 / 271 |
| D3418 | Glass Transition Temp (°F / °C) | 527 / 275 |
| - | Max Operating Temp (°F / °C) | 500 / 260 |
| C177 | Thermal Conductivity (BTU-in/ft²-hr-°F) (x 10-4 cal/cm-sec-°C) |
2.5 8.6 |
| UL94 | Flammability Rating | V-0 |
| ELECTRICAL | ||
| D149 | Dielectric Strength (V/mil) short time, 1/8" thick | - |
| D150 | Dielectric Constant at 1 MHz | - |
| D150 | Dissipation Factor at 1 MHz | - |
| EOS/ESD S11.11 | Surface Resistivity (ohms/square) | > 1013 |
NOTE: The information contained herein are typical values intended for reference and comparison purposes only. They should NOT be used as a basis for design specifications or quality control. Contact us for manufacturers' complete material property datasheets.DURATRON is a registered trademark of Quadrant Engineering Plastic Products.
All values at 73°F (23°C) unless otherwise noted.
©
Copyright Boedeker Plastics, Inc.